Open Access
Issue
E3S Web of Conf.
Volume 405, 2023
2023 International Conference on Sustainable Technologies in Civil and Environmental Engineering (ICSTCE 2023)
Article Number 02010
Number of page(s) 12
Section Renewable Energy & Electrical Technology
DOI https://doi.org/10.1051/e3sconf/202340502010
Published online 26 July 2023
  1. Babu, B., et al. “Design and Fabrication Of Pressing Steam Boiler.” International Journal of Current Trends in Engineering & Research 2.4 (2016): 461–473. [Google Scholar]
  2. Davidson, W. F., et al. “Studies of heat transmission through boiler tubing at pressures from 500 to 3300 pounds.” Transactions of the American Society of Mechanical Engineers 65.6 (1943): 553–579. [Google Scholar]
  3. Nayak, Purusottam. “Problems and prospects of rice mill modernization A case study.” (2010).S [Google Scholar]
  4. Senthil Kumaran, S., and A. Daniel Das. “An investigation of Boiler Grade Tube and Tube Plate without block by using friction welding process.” Materials Today: Proceedings 5.2 (2018): 8567–8576. [CrossRef] [Google Scholar]
  5. Dehnavi, F., A. Eslami, and F. Ashrafizadeh. “A case study on failure of superheater tubes in an industrial power plant.” Engineering Failure Analysis 80 (2017): 368–377. [CrossRef] [Google Scholar]
  6. V. Chawla, A. Chawla, D. Puri, S. Prakash, P. Gurbuxani and B. Sidhu, “Hot Corrosion & Erosion Problems in Coal Based Power Plants in India and Possible Solutions – A Review,” Journal of Minerals and Materials Characterization and Engineering, Vol. 10 No. 4, 2011, pp. 367–386. doi: 10.4236/jmmce.2011.104027. [CrossRef] [Google Scholar]
  7. Kumar, K., Kumar, S. and Gill, H.S. (2022), “Role of Surface Modification Techniques to Prevent Failure of Components Subjected to the Fireside of Boilers”, Journal of Failure Analysis and Prevention, DOI: 10.1007/s11668-022-01556-w. [Google Scholar]
  8. Kumar, S., Kumar, M. (2022), “Tribological and Mechanical Performance of Coatings on Piston to Avoid Failure—A Review”. J Fail. Anal. And Preven. Vol. 22 pp. 1346–1369. https://doi.org/10.1007/s11668-022-01436-3 [CrossRef] [Google Scholar]
  9. Kumar, S., Kumar, M., and Handa, A., (2018), “Combating Hot Corrosion of Boiler Tubes- A Study”, Engineering Failure Analysis, Vol. 94, pp. 379–395. https://doi.org/10.1016/j.engfailanal.2018.08.004 [CrossRef] [Google Scholar]
  10. Kumar, S. (2022), “Influence of processing conditions on the mechanical, tribological and fatigue performance of cold spray coating: A Review”, Surface Engineering, Vol. 38 (4), pp. 324–365. https://doi.org/10.1080/02670844.2022.2073424 [CrossRef] [Google Scholar]
  11. Kumar, S. and Kumar, R. (2021), “Influence of processing conditions on the properties of thermal sprayed coating: a review”, Surface Engineering, Vol. 37 (11), pp. 1339–1372. https://doi.org/10.1080/02670844.2021.1967024. [CrossRef] [Google Scholar]
  12. Kumar, S., Kumar, M., Handa, A., (2020), “Erosion corrosion behavior and mechanical property of wire arc sprayed Ni-Cr and Ni-Al coating on boiler steels in actual boiler environment”, Material at High Temperature, Volume 37 (6), pp. 370–384. https://doi.org/10.1080/09603409.2020.1810922. [CrossRef] [Google Scholar]
  13. Kumar, M., Kant, S., Kumar, S., (2019), “Corrosion behavior of wire arc sprayed Ni- based coatings in extreme environment”, Materials Research Express, Vol. 6 (10), pp.106427. https://doi.org/10.1088/2053-1591/ab3bd8 [CrossRef] [Google Scholar]
  14. Kumar, S., Kumar, M., Handa, A., (2019), “Comparative Study of High Temperature Oxidation Behavior of Wire Arc Sprayed Ni-Cr and Ni-Al Coatings”, Engineering Failure Analysis, Vol. 106, pp. 104173–104189. https://doi.org/10.1016/j.engfailanal.2019.104173 [CrossRef] [Google Scholar]
  15. Sharma, V., Kumar, S., Kumar, M., Deepak, D., (2020), “High Temperature Oxidation Performance of Ni-Cr-Ti and Ni-5Al Coatings”, Material Today Proceeding, Vol. 26 (3), pp. 3397–3406. https://doi.org/10.1016/j.matpr.2019.11.048. [CrossRef] [Google Scholar]
  16. Singh, H., Kumar, S. and Kumar, R. (2021), “Overview of Corrosion and its Control: A Critical Review”, Proceedings on Engineering Sciences”, Vol. 3 (1), pp. 13–24. DOI: 10.24874/PES03.01.002.http://pesjournal.net/journal/v3-n1/2.pdf. [CrossRef] [Google Scholar]
  17. P. Ateb Ubi (2010), “Design, Fabrication and Testing of A Steam Generator” Thesis, Federal University Of Technology, Minna, pp. 1–78. [Google Scholar]
  18. Peerapong, P. and Limmeechokchai, B. (2009), “Thermodynamic and Economic Analysis of 1.4 MWe Rice-Husk Fired Cogeneration in Thailand”, International Journal of Renewable Energy, Vol. 4, No. 2, pp. 1–12. https://www.thaiscience.info/journals/Article/IIRE/10895222.pdf [Google Scholar]

Current usage metrics show cumulative count of Article Views (full-text article views including HTML views, PDF and ePub downloads, according to the available data) and Abstracts Views on Vision4Press platform.

Data correspond to usage on the plateform after 2015. The current usage metrics is available 48-96 hours after online publication and is updated daily on week days.

Initial download of the metrics may take a while.