Open Access
Issue
E3S Web Conf.
Volume 500, 2024
The 1st International Conference on Environment, Green Technology, and Digital Society (INTERCONNECTS 2023)
Article Number 03004
Number of page(s) 7
Section Engineering and Technology
DOI https://doi.org/10.1051/e3sconf/202450003004
Published online 11 March 2024
  1. R. D. Anjani, A. E. Nugraha, R. P. Sari, dan D. T. Santoso, “Perancangan Alat Bantu Kerja Dengan Menggunakan Metode Antropometri Dan Material Selection,” J. Teknol., vol. 13, no. 1, hal. 15–24, 2021. [Google Scholar]
  2. Y. A. Fatimah, K. Govindan, R. Murniningsih, dan A. Setiawan, “Industry 4.0 based sustainable circular economy approach for smart waste management system to achieve sustainable development goals: A case study of Indonesia,” J. Clean. Prod., vol. 269, 2020, doi: 10.1016/j.jclepro.2020.122263. [CrossRef] [Google Scholar]
  3. S. A. Irawan, “Jurnal Anggaran dan Keuangan Negara Indonesia DAMPAK PANDEMI COVID-19 TERHADAP IMPLEMENTASI MAKING INDONESIA 4.0 Impact of The Covid-19 Pandemic on The Implementation of Making Indonesia 4.0,” J. Anggar. dan Keuang. Negara Indones., vol. 3, no. 2, 2021. [Google Scholar]
  4. [Nelfiyanti, Casban, R. A. M. Puteri, A. I. Ramadhan, dan E. Diniardi, “Penerapan PDCA Dalam Meminimasi Cacat Produk Scratch Di,” Pros. Semniar Nas. Penelit. LPPM UMJ, 2020. [Google Scholar]
  5. Ruslan Supriyadi, Suwaryo Nugroho, dan Kristanto Mulyono, “Meningkatkan produktivitas pada line produksi di PT. XYZ dengan menggunakan metode PDCA delta,” JENIUS J. Terap. Tek. Ind., vol. 3, no. 1, hal. 51–60, 2022, doi: 10.37373/jenius.v3i1.235. [CrossRef] [Google Scholar]
  6. E. L. Miftahul Imtihan, “Perancangan Produk Aquascape Dengan Metode Quality Function Deployment (QFD),” JENIUS J. Terap. Tek. Ind., 2020, doi: 10.37373/jenius.v1i1.24. [Google Scholar]
  7. M. Khotib, M. H. Basri, D. A. Surya, dan H. S. Iskawanto, “Perancangan Sistem Kontrol Heater Mesin Grinder Coffee Brewer Otomatis Menggunakan Metode Kontrol PI (Proportional Integral),” Rekayasa, vol. 14, no. 3, hal. 296–300, 2021, doi: 10.21107/rekayasa.v14i3.11381. [CrossRef] [Google Scholar]
  8. M. Hastarina, A. Ansyori Masruri, dan S. Adi Saputra, “Perancangan Mesin Peleleh Biji Plastik Sebagai Alternatif Pengolahan Limbah Plastik dengan Penerapan Metode Value Engineering Design of Plastic Injection Molding as an Alternative to Plastic Waste Treatment by Using Value Engineering Method,” Integr. J. Ilm. Tek. Ind., vol. 2, no. 6, hal. 49, 2019. [Google Scholar]
  9. F. Azharul, Rahmawati, Choiruddin, dan Wilarso, “Rancang Bangun Alat Kalibrasi Pengukur Suhu Berbasis Digital Temperatur Controller,” TEKNOSAINS J. Sains, Teknol. dan Inform., vol. 8, no. 2, hal. 109–116, 2021, doi: 10.37373/tekno.v8i2.103. [CrossRef] [Google Scholar]
  10. A. Pramono, “Perlakuan Panas Paduan Aluminium Berbutir Halus Ultrafine Grained Hasil Teknologi Severe Plastic Deformation,” Tek. J. Sains dan Teknol., vol. 14, no. 2, hal. 107, 2018, doi: 10.36055/tjst.v14i2.5866. [CrossRef] [Google Scholar]
  11. D. Irwansyah, C. Budiyantoro, dan Sunardi, “Perancangan Mesin Vacuum Forming Untuk Material Plastik Polystyrene (Ps) Dengan Ukuran Maksimal Cetakan,” Mater. dan Proses Manufaktur, vol. 1, no. 2, hal. 87–95, 2017. [Google Scholar]
  12. I. Okatama, “Analisa Peleburan Limbah Plastik Jenis Polyethylene Terphtalate (Pet) Menjadi Biji Plastik Melalui Pengujian Alat Pelebur Plastik,” J. Tek. Mesin, vol. 5, no. 3, hal. 20, 2017, doi: 10.22441/jtm.v5i3.1213. [Google Scholar]
  13. H. Ramadhani, P. Yongki, dan R. Fitriani, “Analisis Perancangan Alat Bantu pada Mesin Slitter Menggunakan Metode AHOQ,” vol. 12, no. 2, hal. 117–124, 2022. [Google Scholar]
  14. I. Okatama, “Analisa Peleburan Limbah Plastik Jenis Polyethylene,” J. Tek. Mesin, vol. 05, no. 3, hal. 109–113, 2016. [Google Scholar]
  15. I. Yulianto, Rispianda, dan H. Prassetiyo, “Rancangan Desain Mold Produk Knob Regulator Kompor Gas pada Proses Injection Molding,” Reka Integr., vol. 2, no. 3, hal. 140–151, 2014. [Google Scholar]
  16. K. Nabila dan R. Rochmoeljati, “Analisis Pengendalian Kualitas Menggunakan Metode Six Sigma Dan Perbaikan Dengan Kaizen,” Juminten, vol. 1, no. 1, hal. 116–127, 2020, doi: 10.33005/juminten.v1i1.27. [Google Scholar]
  17. R. Usman dan N. Nanang, “Kualitas Produksi Plastic Moulding Decorative Printing Metode Six Sigma Failure Mode Effect Analysis (Fmea) Kemasan Cat Plastik,” J. Teknol., vol. 13, no. 1, hal. 25–32, 2021. [Google Scholar]

Current usage metrics show cumulative count of Article Views (full-text article views including HTML views, PDF and ePub downloads, according to the available data) and Abstracts Views on Vision4Press platform.

Data correspond to usage on the plateform after 2015. The current usage metrics is available 48-96 hours after online publication and is updated daily on week days.

Initial download of the metrics may take a while.