Open Access
Issue
E3S Web Conf.
Volume 221, 2020
Energy Systems Environmental Impacts (ESEI 2020)
Article Number 03007
Number of page(s) 9
Section Power Engineering
DOI https://doi.org/10.1051/e3sconf/202022103007
Published online 17 December 2020
  1. Asgarshamsi, A., Hajilouy-Benisi, A., Assempour, A., Pourfarzaneh, H. (2017). Multipoint optimization of lean and sweep angles for stator and rotor blades of an axial turbine. Iranian Journal of Science and Technology Transactions of Mechanical Engineering, 41(1), pp. 35-47. [CrossRef] [Google Scholar]
  2. Dong, Y. W., Li, X. L., Zhao, Q., Yang, J., Dao, M. (2017). Modeling of shrinkage during investment casting of thin-walled hollow turbine blades. Journal of Materials Processing Technology, 244, pp. 190-203. [CrossRef] [Google Scholar]
  3. Emelyanov, I. P., Ageev, E. V. (2015). Balancing features of car engine turbine compressors. International Journal of Applied Engineering Research, 10(24), pp. 45003-45006. [Google Scholar]
  4. Klochkov, Y., Gazizulina, A. (2016). Application of the method of performance evaluation of the production proceb design using abociative design. Key Engineering Materials, 684, pp. 448-452. [Google Scholar]
  5. Klochkov, Y., Gazizulina, A. (2016). Improvement of methodology of evaluation of efficiency of the etallurgical complex procebes development. Key Engineering Materials, 684, pp. 453-460. [Google Scholar]
  6. Lang, G., Lin, J., Liao, Y., Zhao, M. (2017). Impact of system anisotropy on vibration reduction of rotating machinery and its evaluation method. Mechanical Systems and Signal Processing, 93, pp. 299-311. [Google Scholar]
  7. Müller-Vahl, H. F., Pechlivanoglou, G., Nayeri, C. N., Paschereit, C. O., Greenblatt, D. (2017). Matched pitch rate extensions to dynamic stall on rotor blades. Renewable Energy, 105, pp. 505-519. [Google Scholar]
  8. Payne, G. S., Stallard, T., Martinez, R. (2017). Design and manufacture of a bed supported tidal turbine model for blade and shaft load measurement in turbulent flow and waves. Renewable Energy, 107, pp. 312-326. [Google Scholar]
  9. Sandberg, D., Mansour, R., Olsson, M. (2017). Fatigue probability assessment including aleatory and epistemic uncertainty with application to gas turbine compressor blades. International Journal of Fatigue, 95, pp. 132-142. [Google Scholar]
  10. Swamy, M., Singh, K., Pavan, A. H. V. Antony Harison, M. C., Jayaraman, G. (2016). Failure Investigation of Frame 6FA Gas Turbine Compressor Blades. Transactions of the Indian Institute of Metals, 69(2), pp. 647-651. [CrossRef] [Google Scholar]
  11. Tiralap, A., Tan, C. S., Donahoo, E., Montgomery, M., Cornelius, C. (2017). Effects of rotor tip blade loading variation on compressor stage performance. Journal of Turbomachinery, 139(5), 051006. [Google Scholar]
  12. Wood, D. H., Okulov, V. L. (2017). Nonlinear blade element-momentum analysis of Betz-Goldstein rotors. Renewable Energy, 107, pp. 542-549. [Google Scholar]
  13. Xie, F., Ma, H., Cui, C., Wen, B. (2017). Vibration response comparison of twisted shrouded blades using different impact models. Journal of Sound and Vibration, 397, pp. 171-191. [Google Scholar]
  14. Zhao, F., Smith, N., Vahdati, M. (2017). A simple model for identifying the flutter bite of fan blades. Journal of Turbomachinery, 139(7), 071003. [Google Scholar]
  15. Zhao, Z., Fu, Y., Liu, X., Xu, J., Wang, J., Mao, S. (2017). Measurement-based geometric reconstruction for milling turbine blade using free-form deformation. Measurement: Journal of the International Measurement Confederation, 101, pp. 19-27. [CrossRef] [Google Scholar]
  16. Zvonov, S., Klochkov, Y. (2016). Computer-aided modelling of a latch die cutting in Deform -2D software system. Key Engineering Materials, 685, pp. 811-815. [Google Scholar]
  17. Polyakova, M.A., Rubin, G.S., Gun, G.S., Danilova, Y.V. (2016). New approach to development methodology of requirements of standards for metal products. CIS Iron and Steel Review, 12, pp. 45-49. [CrossRef] [Google Scholar]
  18. Rubin, G.S., Polyakova, M.A., Chukin, M.V., Gun, G.S. (2013). Document Protypology: A new stage in the standardization of metal products. Steel in Translation, 43 (10), pp. 666-669. [CrossRef] [Google Scholar]

Current usage metrics show cumulative count of Article Views (full-text article views including HTML views, PDF and ePub downloads, according to the available data) and Abstracts Views on Vision4Press platform.

Data correspond to usage on the plateform after 2015. The current usage metrics is available 48-96 hours after online publication and is updated daily on week days.

Initial download of the metrics may take a while.