Effect of High Speed Machining on Surface Roughness Characteristics Ra, Rq, RZ

Open Access

Issue		E3S Web Conf. Volume 430, 2023 15^th International Conference on Materials Processing and Characterization (ICMPC 2023)


Article Number		01271
Number of page(s)		14
DOI		https://doi.org/10.1051/e3sconf/202343001271
Published online		06 October 2023

S. Kumar Khare and G. Singh Phull, “Analysis and optimization of machining parameters of Ti-6Al-4 V under high-speed machining,” Mater. Today Proc., vol. 62, no. xxxx, pp. 3097–3102, 2022, doi: 10.1016/j.matpr.2022.03.255. [CrossRef] [Google Scholar]
S. Raghavendra, P. S. Sathyanarayana, S. K. S, T. Vs, and M. Kn, “High speed machining of titanium Ti 6Al4V alloy components: study and optimisation of cutting parameters using RSM,” Adv. Mater. Process. Technol., vol. 00, no. 00, pp. 1–14, 2020, doi: 10.1080/2374068X.2020.1806684. [Google Scholar]
C. Bandapalli, B. M. Sutaria, and D. V. Bhatt, “High speed machining of ti-alloys-A critical review,” 1st Int. 16th Natl. Conf. Mach. Mech. Ina. 2013, no. Cm, pp. 324–331, 2013. [Google Scholar]
N. Fang and Q. Wu, “A comparative study of the cutting forces in high speed machining of Ti-6Al-4V and Inconel 718 with a round cutting edge tool,” J. Mater. Process. Technol., vol. 209, no. 9, pp. 4385–4389, 2009, doi: 10.1016/j.jmatprotec.2008.10.013. [CrossRef] [Google Scholar]
M. Tools, “<130 High Speed Milling Of Titanium Alloys Kaynaklarından Kaynak Çıkar.pdf>,” vol. 3, pp. 131–140, 2008. [Google Scholar]
S. K. Khare, G. S. Phull, and S. Agarwal, “Optimization the Machining Parameters of Surface Roughness during Micro-EDM by Taguchi Method,” Mater. Today Proc., vol. 27, no. xxxx, pp. 475–479, 2020, doi: 10.1016/j.matpr.2019.11.279. [CrossRef] [Google Scholar]
V. Krishnaraj, S. Samsudeensadham, R. Sindhumathi, and P. Kuppan, “A study on high speed end milling of titanium alloy,” Procedia Eng., vol. 97, pp. 251–257, 2014, doi: 10.1016/j.proeng.2014.12.248. [CrossRef] [Google Scholar]
N. Khanna, K. Zadafiya, T. Patel, Y. Kaynak, R. A. Rahman Rashid, and A. Vafadar, “Review on machining of additively manufactured nickel and titanium alloys,” J. Mater. Res. Technol., vol. 15, pp. 3192–3221, 2021, doi: 10.1016/j.jmrt.2021.09.088. [CrossRef] [Google Scholar]
M. Chand, A. Mehta, R. Sharma, V. N. Ojha, and K. P. Chaudhary, “Roughness measurement using optical profiler with self-reference laser and stylus instrument - A comparative study,” Indian J. Pure Appl. Phys., vol. 49, no. 5, pp. 335–339, 2011. [Google Scholar]
W. dos Santos Motta Neto, J. E. S. Leal, L. J. Arantes, and R. V. Arencibia, “The effect of stylus tip radius on Ra, Rq, Rp, Rv, and Rt parameters in turned and milled samples,” Int. J. Adv. Manuf. Technol., vol. 99, no. 5–8, pp. 1979–1992, 2018, doi: 10.1007/s00170-018-2630-5. [CrossRef] [Google Scholar]
R. K. Leach, “The measurement of surface texture using stylus instruments.,” Meas. Good Pract. Guid. No. 37, no. 2, p. 100, 2001, [Online]. Available: http://publications.npl.co.uk/npl_web/pdf/mgpg37.pdf [Google Scholar]
M. R. Ch and V. Kambagowni, “Experimental Investigation of Surface Roughness Characteristics Ra , Rq and Experimental Investigation of Surface Roughness Characteristics R a , R q and R z,” no. July, 2016, doi: 10.14257/ijhit.2016.9.7.34. [Google Scholar]
P. S. Rao, K. Ramji, and B. Satyanarayana, “EFFECT OF WEDM CONDITIONS ON SURFACE ROUGHNESS:,” no. January, 2016. [Google Scholar]
K. Universiti, T. Tun, and H. Onn, “Analyses of surface roughness by turning process using Taguchi method,” vol. 20, pp. 503–506, 2007. [Google Scholar]
S. K. Khare, G. S. Phull, R. K. Verma, and S. Agarwal, “A comparison between optimization techniques of cutting parameters under cryogenic machining process,” Mater. Today Proc., vol. 26, no. xxxx, pp. 2697–2700, 2019, doi: 10.1016/j.matpr.2020.02.567. [CrossRef] [Google Scholar]
T. Sivaprakasam, “Analyses of surface roughness by turning process using Taguchi method,” no. April 2015, 2007. [Google Scholar]
J. Kumar, T. Soota, S. K. Rajput, and K. K. Saxena, “Machining and optimization of Zircaloy-2 using different tool electrodes,” Mater. Manuf. Process., vol. 00, no. 00, pp. 1–11, 2021, doi: 10.1080/10426914.2021.1905829. [Google Scholar]

Current usage metrics show cumulative count of Article Views (full-text article views including HTML views, PDF and ePub downloads, according to the available data) and Abstracts Views on Vision4Press platform.

Data correspond to usage on the plateform after 2015. The current usage metrics is available 48-96 hours after online publication and is updated daily on week days.

Initial download of the metrics may take a while.